图3-1 RIP配置网络拓扑 3.1 RIP基础配置 1.配置R1接口IP及LoopBack 0接口IP地址 [R1]interface LoopBack 0 [R1-LoopBack0]ip address 1.1.1.1 32 2.配置R2接口IP及LoopBack 0接口IP地址 [R2]int...

图3-2 RIP手动路由汇总配置网络拓扑 1.R1基本配置 [R1]interface LoopBack 0 [R1-LoopBack0]ip address 1.1.1.1 24 [R1-LoopBack0]quit [R1-LoopBack0]ip address 1.1.2.1 24 sub [R1-LoopBack0...

图3-3 RIP明文及MD5认证配置网络拓扑 1.R1、R2之间做明文认证 [R1]interface GigabitEthernet 0/0/0 [R1-GigabitEthernet0/0/0]rip authentication-mode simple dsrw.com [R2]interface Gigabit...

图3-4 RIP抑制接口配置网络拓扑 1.R2上抑制连接R1的接口，稍后观察R1、R2的RIP路由表 [R2]rip 1 [R2-rip-1]silent-interface GigabitEthernet 0/0/0 <R1>display ip routing-table protocol ...

图3-5 RIPv1与 RIPv2兼容配置网络拓扑 1.R3配置RIPv1 [R3]rip 1 [R3-rip-1]version 1 2.查看R2配置RIP路由，无R3路由 [R2]display ip routing-table protocol rip Destination/Mask Proto Pre C...

图4-1 OSPF基本配置网络拓扑 图4-2 OSPF基本单区域配置网络拓扑 1.R1配置单区域OSPF [R1]ospf 1 router-id 1.1.1.1 [R1-ospf-1]area 0 [R1-ospf-1-area-0.0.0.0]network 1.1.1.1 0.0.0.0 [R1-os...

1.查看R1、R2之间DR和BDR信息 <R1>display ospf peer OSPF Process 1 with Router ID 1.1.1.1 Neighbors Area 0.0.0.0 interface 12.1.1.1(GigabitEthernet0/0/0)'s neighbors Router ID: 2....

图4-3  配置OSPF接口的网络类型网络拓扑 1.查看R1路由表，R2、R3环回口路由为32位主机路由 [R1]display ip routing-table protocol ospf 2.2.2.2/32 OSPF 10 1 D 12.1.1.2 GigabitEthernet0/0/...

1.在R1查看R2环回接口的OSPF的COST值 <R1>display ip routing-table protocol ospf Destination/Mask Proto Pre Cost Flags NextHop Interface 2.2.2.2/32 OSPF 10 1 D 12.1.1.2 GigabitEthe...

1.修改R1的G0/0/0口为Silent-interface类型（静默接口），查看OSPF信息（不收发任何OSPF报文） [R1]ospf 1 [R1-ospf-1]silent-interface GigabitEthernet 0/0/0 [R1]display ip routing-table p...