图1-1 基本配置网络拓扑 1.设备启动模式：用户模式（用户视图），用<>表示 <Huawei> 2.进入特权模式 <Huawei>system-view Enter system view, return user view with Ctrl+Z. [Huawei]...

图2-1 静态路由网络拓扑 1.R1配置 <Huawei>U T M Info: Current terminal monitor is off. <Huawei>system-view Enter system view, return user view with Ctrl+Z. [Huawei]sysname R1 [...

图3-1 RIP配置网络拓扑 3.1 RIP基础配置 1.配置R1接口IP及LoopBack 0接口IP地址 [R1]interface LoopBack 0 [R1-LoopBack0]ip address 1.1.1.1 32 2.配置R2接口IP及LoopBack 0接口IP地址 [R2]int...

图12-1 telnet配置网络拓扑 1.R2配置 [R2]interface GigabitEthernet 0/0/0 [R2-GigabitEthernet0/0/0]ip address 12.1.1.2 8 [R2]aaa [R2-aaa]local-user dsrw password cipher dsrw.com [R2-a...

图15-1 GRP隧道配置网络拓扑 1.配置R1、R2、R3间OSPF路由 [R1]ospf 1 [R1-ospf-1-area-0.0.0.0]network 12.1.1.0 0.255.255.255 [R2-ospf-1]area 0 [R2-ospf-1-area-0.0.0.0]network 12.1.1.0 0...

1.修改R1的G0/0/0口为Silent-interface类型（静默接口），查看OSPF信息（不收发任何OSPF报文） [R1]ospf 1 [R1-ospf-1]silent-interface GigabitEthernet 0/0/0 [R1]display ip routing-table p...

图3-2 RIP手动路由汇总配置网络拓扑 1.R1基本配置 [R1]interface LoopBack 0 [R1-LoopBack0]ip address 1.1.1.1 24 [R1-LoopBack0]quit [R1-LoopBack0]ip address 1.1.2.1 24 sub [R1-LoopBack0...

图8-6 STP配置网络拓扑 1.配置STP [sw1]stp enable [sw1]stp mode stp [sw2]stp enable [sw2]stp mode stp [SW3]stp enable [SW3]stp mode stp 2.查看STP状态信息 [sw1]display stp -------[CIS...

图11-1 AAA本地认证网络拓扑 1.R2配置 [R2]interface GigabitEthernet 0/0/0 [R2-GigabitEthernet0/0/0]ip address 12.1.1.2 8 [R2]aaa [R2-aaa]authentication-scheme default [R2-aaa-authen-...

图4-3  配置OSPF接口的网络类型网络拓扑 1.查看R1路由表，R2、R3环回口路由为32位主机路由 [R1]display ip routing-table protocol ospf 2.2.2.2/32 OSPF 10 1 D 12.1.1.2 GigabitEthernet0/0/...