图6-1 交换机基本配置网络拓扑 1.初始状态交换机MAC地址表为空 [SW1]display mac-address 2.PC1去ping未知IP地址192.168.1.3，在PC2接口抓包 图6-2 SW3 G0/0/1口抓包 3.查看SW1交换机MAC地址表,...

图8-5 GVRP配置网络拓扑 1.SW1配置G24口为trunk模式，允许所有VLAN通过 [SW1]interface GigabitEthernet 0/0/24 [SW1-GigabitEthernet0/0/24]port link-type trunk [SW1-GigabitEthernet0/0/24]...

图3-1 RIP配置网络拓扑 3.1 RIP基础配置 1.配置R1接口IP及LoopBack 0接口IP地址 [R1]interface LoopBack 0 [R1-LoopBack0]ip address 1.1.1.1 32 2.配置R2接口IP及LoopBack 0接口IP地址 [R2]int...

图4-8  FR环境下配置OSPF网络拓扑 图4-9  FR配置网络拓扑 1.R1配置 [R1]interface Serial 0/0/0 [R1-Serial0/0/0]link-protocol fr ietf [R1-Serial0/0/0]undo fr inarp [R1-Serial0/0/0]ip a...

图8-4 hybrid接口混合模式配置网络拓扑 1.实验要求 1）R1、R3互访 2）R2、R3互访 3）R1、R4互访 4）R3、R5互访 5）其余之间不能互访 2.SW1配置 [SW1]vlan batch 10 20 30 [SW1]interface Gigabi...

图20-1 静态IPsec VPN配置网络拓扑 1.配置R1、R3ACL感兴趣流 [R1]acl 3000 [R1-acl-adv-3000]rule permit ip source 192.168.1.0 0.0.0.255 destination 192.168.3.0 0.0.0.255 [R3]acl 3000 [R...

1.router-id一致故障 [R2]ospf 1 router-id 1.1.1.1 Info: The configuration succeeded. You need to restart the OSPF process to validate the new router ID. 2.重启OSPF进程 <R2>reset ...

图19-4 OSPFv3基本配置网络拓扑 1.R1配置OSPFv3 [R1]ospfv3 1 [R1-ospfv3-1]router-id 1.1.1.1 [R1]interface GigabitEthernet 0/0/0 [R1-GigabitEthernet0/0/0]ospfv3 1 area 0 [R1]interface ...

图9-1 VLAN间路由配置网络拓扑 1.SW1配置VLAN [SW1]vlan batch 10 30 [SW1]interface GigabitEthernet 0/0/1 [SW1-GigabitEthernet0/0/1]port link-type access [SW1-GigabitEthernet0/0/1]port...

1.查看OSPF路由优先级，内部OSPF优先级10，外部150 <R1>display ip routing-table protocol ospf 34.0.0.0/8 OSPF 10 12 D 12.1.1.2 GigabitEthernet0/0/0 44.1.0.0/22 O_ASE 150 2 D 12.1.1...