18.2 PPPoE client端配置
1.创建拨号规则 [R1]dialer-rule [R1-dialer-rule]dialer-rule 1 ip permit //允许ip流量触发拨号 [R1-dialer-rule]quit 2.创建拨号虚拟接口 [R1]interface Dialer 1 [R1-Dialer1]dialer user d...
18.6 端口镜像
1.一对一本地接口镜像：配置SW1的G0/0/24端口为镜像端口，G0/0/1端口为观察端口。 图18-7 一对一本地接口镜像配置网络拓扑 [SW1]observe-port 1 interface GigabitEthernet 0/0/1 //配置Gigabit...
18.7 负载分担VRRP
图18-11 负载分担VRRP配置网络拓扑 1.R2配置VRRP [R2]interface GigabitEthernet 0/0/1 [R2-GigabitEthernet0/0/1]vrrp vrid 1 virtual-ip 23.1.1.254 [R2-GigabitEthernet0/0/1]vrrp vrid 1 pr...
18.8 BFD基础
图18-12 BFD单跳检测链路配置网络拓扑 1.配置BFD单跳检测链路 1）R1配置 [R1]bfd [R1]bfd R1toR2 bind peer-ip 12.1.1.2 interface GigabitEthernet 0/0/0 //创建三层链路单跳检测的BFD会话R1to...
18.9 VRF基础
1.静态路由方式配置VRF 图18-20 静态路由方式配置VRF网络拓扑 1）R1创建vpn-instance R2，下行端口绑定vpn-instance R2 [R1]ip vpn-instance R2 [R1-vpn-instance-R2]ipv4-family [R1]interface...
第19章 IPV6及OSPF3-19.1 IPV6配置
图19-1 IPV6基本配置网络拓扑 1.R1配置 [R1]IPV6 [R1]interface GigabitEthernet 0/0/0 [R1-GigabitEthernet0/0/0]ipv6 enable [R1-GigabitEthernet0/0/0]ipv6 address 2002::1 64 [R1]interfac...
19.2 OSPFv3配置
图19-4 OSPFv3基本配置网络拓扑 1.R1配置OSPFv3 [R1]ospfv3 1 [R1-ospfv3-1]router-id 1.1.1.1 [R1]interface GigabitEthernet 0/0/0 [R1-GigabitEthernet0/0/0]ospfv3 1 area 0 [R1]interface ...
第20章 IPsec VPN-20.1 静态IPsec VPN配置
图20-1 静态IPsec VPN配置网络拓扑 1.配置R1、R3ACL感兴趣流 [R1]acl 3000 [R1-acl-adv-3000]rule permit ip source 192.168.1.0 0.0.0.255 destination 192.168.3.0 0.0.0.255 [R3]acl 3000 [R...
20.2 IKE 动态IPsec VPN配置
图20-2 IKE 动态IPsec VPN配置网络拓扑 1.配置R1、R3ACL感兴趣流 [R1]acl 3000 [R1-acl-adv-3000]rule permit ip source 192.168.1.0 0.0.0.255 destination 192.168.3.0 0.0.0.255 [R3]acl 300...
20.3 IPsec VPN与源NAT配置
1.R1配置 [R1]acl 3001 [R1-acl-adv-3001]rule deny ip source 192.168.1.0 0.0.0.255 destination 192.168.3.0 0.0.0.255 [R1-acl-adv-3001]rule permit ip source 192.168.1.0 0.0.0.255 2.R3...
